我的GIGABYTE Brix BLPD-5005折腾记录

December 17, 2018 Categories:随便写写 No Comments yet

早买早享受,晚买真特么便宜。899元入手了技嘉Brix BLPD-5005,J东PLUS会员849元。大陆版不含INTEL AC3168无线网卡,尽管卖家送了一个2.4G的单频网卡,但是怎么够用呢,2.4G严重污染的今天我宁可它只支持5.8G。所以又淘宝了一个intel 9260AC A+E Key,结果只能识别到蓝牙。被服务员误导了,见图

Screenshot_20181216-161435.png

实际等我收到机器发现:

IMG_20181216_165227730.jpg

不得不重新购入9560AC,KEY E接口。满网找不到这款机器的使用分享,也没主板接口图,这也是我写这篇文的原因。目前看来在支持CNVI的主板上还是要选9560,不要选9260. 9560和9260区别是硬件接口不同,一个ekey 一个ae key,技术方面9560是cnvi技术,而9260则不是,其它参数则完全一致。难道cnvi是不向下兼容的吗?还是只限于9260这款不兼容呢?毕竟有一个完全相同规格的9560? 如果你知道请告知。迫击炮9260ac只有蓝牙intel9560ac兼容的平台

在闲鱼买到两条戴尔机器升级换下来的4G镁光DDR2666(淘宝的低价镁光倒不都是假货但是双面的老产品);HP EX900 256G Nvme券后价259块,不买对不起卖家。

IMG_20181216_122402113.jpg

总体上,除了WIFI CARD出了岔子,整个采购过程还是比较满意的~ 卖家也都没有因为做活动而发用过的产品(ORZ,以前买过一个京东自营的飞利浦空气炸锅,显示最后一台,结果东西被用过。所以我遇到京东自营搞大幅活动而且最后一台的情况都是忽略,换货倒是爽快的。这也是二手东一个特色吧。)

IMG_20181215_112940662.jpg


如果你查看技嘉官方网站无论国际版还是国内版,都会得到这样的参数:

平台最大支持8G内存,固态硬盘支持 M.2 slot (2280_storage) PCIe X2/SATA
WIFI卡支持 PCIe M.2 NGFF 2230 A-E key slot occupied by the WiFi+BT card

而实际上它不仅支持Nvme SSD也支持更快的E KEY Intel 9560ac。关于内存,我没测试,记得某个淘宝店说过16G没问题。但,你得先更新BIOS。官网产品页下载: 官网

下载下来解压缩得到F3_BIOS文件夹,把它放到你的U盘里,以防万一使用FAT32格式分区。由于此时我的硬盘是空的,开机会自动引导到自带的SHELL下,像是这样SHELL>,而在它的上方会显示你插入的U盘盘符,如图,我的被识别为fs0(数字零不是字母欧).

IMG_20181215_132813628.jpg

在SHELL>下输入fs0:回车,然后进入F3_BIOS文件夹(cd空格F3_BIOS回车),再输入FLASH.NSH回车就开始刷新BIOS了,此刻不要乱动,它大概需要几分钟的时间,直到自动重启就代表成功了(它开机本来就慢所以重启黑屏几秒别害怕)。如图(可能比你的多了几个文件同,那是我干的,不用理会,当时想用界面模式刷新,但是明显这个办法更快捷方便):

IMG_20181215_132857365.jpg

IMG_20181215_132916774.jpg

这个BIOS没有特别需要设置的,这时可以愉快地做系统了。

等等,如果你想挑战一下手动分区,然后用DISM++加载镜像做系统的话,可能不会那么的愉快,但我会在下一篇详细写出。

Hackintosh

October 7, 2017 Categories:黑苹果 No Comments yet

我有个500G自组的移动硬盘,USB3接口。其中一个分区是老笔记本用的黑苹果,笔记本是酷睿2平台,当我用得着时会把硬盘抠出来插到笔记本上。我还有个台式机,IVY BRIGE平台,也装有黑苹果,有一次我忘了把这个移动硬盘从台式机上拔掉,玩台式机黑苹果的时候发现不对劲,东西都没了,后来发现居然是引导的移动硬盘上的系统。[摊手]

How to use arduino UNO Flash BLHELI to a turnigy plush 18a esc

July 10, 2017 Categories:随便写写 No Comments yet

I wish I had pc programming skills, then I could reprogram my brushless ESCs to the brushed ESCs.
After I flashed a mod hex of an older plush 30a ESC(with the different MCU. https://launchpad.net/brushed) to my plush 18a but failed.

In order to save my poor ESC, I used BLHELISuite to do this:
Open BlheliSuite, "Make interfaces", make "Arduino 4way-interface", for "SiLabs C2" interface.

Then select "Interfaces" to " SiLabs C2(4way-IF)

Use 3 wires to connect between UNO and ESC, owsilprog-arduino-uno-scheme-02-wp.jpg
Turnigy Plush 25A_30A front.jpg

Then the ESC can be rewritten.
There is a little trick with wire connect, just connect the black wire to GND pin on ESC cable.

RemzibiOSD For Naza

June 26, 2017 Categories:QuadCopter No Comments yet

I made this.
I tied to used an old OSD(short by on-screen display) on phantom2,remzibi osd, but it's a stolen solution from a genuine author I just know, that's a shame. Consequently, it has some issue about updating the new firmware for Naza, so it still needs the decoder board.
I've soldered it over and over again, those procedures drive me crazy…
wx_camera_1498444561403.jpg

Dell d630 with Sierra hackintosh microphone tuning

June 1, 2017 Categories:黑苹果 No Comments yet

Thanks to this entire manual I could installed Sierra to my old laptop: http://forum.osxlatitude.com/index.php?/topic/8645-dell-latitude-d630-with-core2duo-and-nvidia-quadro-nvs-135m-el-capitansierra/

There was a little bit issue when I try to use the microphone. The playback was too loud and noisy. After tuning two values it got a clear sound:
Right click on /Library/Extensions/VooDooHDA.kext "Show package contents", "contents", copy Info.plist to desktop, modify "Boost" integer from "1" to "0", "Rec" integer from "70" to "30", close it and drop back, close all opened window, then open the well-known "Kext Utility" after done, reboot.